iec/en/din en60747-5-2 option 060 for plastic optocoupler data sheet description optocouplers are frequently used to provide high voltage insulation. because optocouplers perform this safety func- tion, they are regulated by many country safety agencies, both at the component level and the equipment level. standard 8 pin dip optocouplers with option 060, are tested according to iec/en/din en60747-5-2 at viorm = 630 vpeak. surface mount so8 optocouplers with option 060, are tested at viorm = 560 vpeak. avago technologies also off ers other various iec/en/din en60747-5-2 approved products at diff erent levels of viorm such as viorm = 1414 vpeak (hcnwxxxx series) and viorm = 891 vpeak (hcpl-jxxx series). refer to the front of the optocoupler section of the isola- tion and control component designers catalog, under product safety regulations section, for a detailed descrip- tion of iec/en/din en60747-5-2 and the partial discharge tests for production option 060 is available on the following products: standard 8 pin dip product (viorm = 630 vpeak) hcpl-2211 hcpl-2212 hcpl-2219 hcpl-2300 hcpl-2400 hcpl-2611 hcpl-261a hcpl-261n hcpl-3120 hcpl-3150 hcpl-4503 hcpl-4504 hcpl-4506 hcpl-4701 hcpl-7840 surface mount so8 product (viorm = 560 vpeak) HCPL-0211 hcpl-0454 hcpl-0466 hcpl-0611 hcpl-061a hcpl-061n hcpl-070a contact your local avago technologies sales representa- tive concerning availability of this option for optocouplers not listed. ordering information specify part number followed by option number. example: hcpl-3120#060 this option may also be combined with option #300 (gull- wing surface mount) or #500 (gullwing in tape and reel). to obtain these combinations, order option #360 or #560 respectively. examples: hcpl-3120 #360 (gullwing surface mount and iec/en/din en60747-5-2 approved) hcpl-3120 #560 (gullwing surface mount and iec/en/din en60747-5-2 approved in tape and reel) marking information a xxxxv yyww date code last 4 digits of part number option 060 8 pin dip package xxxv yww date code last 3 digits of part number option 060 so8 package ur ul recognition* * no ul marking on hcpl-261a/261n/ 3120/3150/4701/7840.
2 parameter symbol value units conditions dip so8 minimum external air gap (external clearance) l(101) 7.1 4.9 mm measured from input terminals to output termi- nals, shortest distance through air. minimum external track ing (external creepage) - l(102) 7.4 4.8 mm measured from input terminals to output termi- nals, shortest distance path along body. minimum internal plastic gap 0.08 0.08 mm through insulation distance, conductor to conductor, usually the direct distance between (internal clearance) the photoemitter and photo- detector inside the optocoupler cavity. tracking resistance (comparative tracking index) cti 175 175 v din iec 112/vde 0303 part 1 isolation group iiia iiia material group (din vde 0110, 1/89, table 1) all avago technologies data sheets report the creepage and clearance inherent to the optocoupler component itself. these dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. however, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specifi ed for individual equipment standards. for creepage, the shortest distance path along the surface of a printed circuit board between the solder fi llets of the input and output leads must be considered. there are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. creep- age and clearance distances will also change depending on factors such as pollution degree and insulation level. figure 1. thermal derating curve, dependence of safety limiting value with case temperature per vde 0884. output power ? p s input current - i s 0 0 200 50 400 125 25 75 100 150 600 800 200 100 300 500 700 175 (150) p s (mw) i s (ma) surface mount so8 product t a - case temperature - o c 0 0 200 50 400 125 25 75 100 150 600 800 200 100 300 500 700 175 (230) p s (mw) i s (ma) standard 8 pin dip product t a - case temperature - o c output power ? p s input current - i s
iec/en/din en60747-5-2 insulation related characteristics (option 060) standard 8 pin dip package *85c: hcpl-2211, hcpl-2212, hcpl-2219, hcpl-2300, hcpl-2400, hcpl-2611, hcpl-261a, hcpl-261n, hcpl-4701, hcpl-7840. **100c: hcpl-3120, hcpl-3150, hcpl-4503, hcpl-4504, hcpl-4506. so8 package *85c: HCPL-0211, hcpl-0611, hcpl-061a, hcpl-061n, hcpl-070a. **100c: hcpl-0454, hcpl-0466. description symbol std. 8 pin dip so8 units installation classifi cation per din vde 0110/1.89, table 1 for rated mains voltage 150 v rms for rated mains voltage 300 v rms for rated mains voltage 450 v rms i-iv i-iv i-iii i-iv i-iii climatic classifi cation 55/85/21* 55/100/21** 55/85/21* 55/100/21** pollution degree (din vde 0110/1.89) 2 2 maximum working insulation voltage v iorm 630 560 v peak input to output test voltage, method b? v iorm x 1.875 = v pr , 100% production test with t m = 1 sec, partial discharge < 5 pc v pr 1181 1050 v peak input to output test voltage, method a? v iorm x 1.5 = v pr , type and sample test, t m = 60 sec, partial discharge < 5 pc v pr 945 840 v peak highest allowable over voltage ? (transient overvoltage, tini = 10 sec) v iotm 6000 4000 v peak safety limiting values (maximum values allowed in the event of a failure, also see thermal derating curve, figure 1.) case temperature input current output power t s i s,input p s,output 175 230 600 150 150 600 o c ma mw insulation resistance at t s , v 10 = 500 v r io ? 10 9 ? 10 9 w ?refer to the front of the optocoupler section of the isolation and control component designers catalog , under product safety regulations section (iec/en/din en60747-5-2), for a detailed description. note: these optocouplers are suitable for safe electrical isolation only within the safety limit data. maintenance of the saf ety data shall be ensured by means of protective circuits. note: the surface mount classifi cation is class a in accordance with cecc 00802. for product information and a complete list of distributors, please go to our web site: www.avagotech.com avago, avago technologies, and the a logo are trademarks of avago technologies in the united states and other countries. data subject to change. copyright ? 2005-2012 avago technologies. all rights reserved. obsoletes 5989-1058en av02-3614en - june 12, 2012
|
